Видео

This is fantastic. Thank you.

How do I get the primer bulb off my Briggs and Stratton 450E so I can replace it?

Thank you for the great video! I was just about to toss my lawnmower in the trash until I did this. This was a Father's Day gift from my boys. Ran out of gas, put in clean gas, and then it died. The only thing I would be careful with is the float metal rod, it falls off easily if you remove it. Thanks again!

thank you for this video. I honestly thought I got a used makita for the reason you described! I feel better

Ummm, well that carb was in horrible shape. I bet the bowl was a total mess. It was gonna die seconds after video cut off. That carb needed complete disassembly and cleaning. Goodness!

Great work! Your explanation in each process helped alot! I have a little 170 that I pair with my 261. They are pretty good little saws for what they are.

❤

Thank you for the excellent video. Exactly what I was looking for

Couldn't you just disconnect the fuel line from the carb and drain it that way

I was told to use a pre-filter over the air filter. And just learned that it's good to oil the pre filter as well. What do you think?

I'm using a different model (Personal Pace AWD) with two belts, but only the front drive suddenly stopped working. I'm going to attempt repair tomorrow morning. However, another guy I asked said those three keeper screws are TORX (star point) rather than Robertson (square point). Does Toro change up screws like that between similar models? Or is that other guy mistaken?

My hrr 216 is slightly different. I did have to remove the housing to be able to rotate the trans to proceed my unit has individual rear wheel adjustments and I adjusted the wheel nearest the trans for extra space. When I was done and placed the unit on the ground the rear wheels will not adjust evenly one has to be set higher 2 spaces higher to be even. Prior to the belt change there was no issue. Any ideas. Also, I did remove the spring but re attached it. Tx

Thank you for the ideas. I only wish I had curbs.

I just want to thank you so much! u probably just saved me $150. SWF and I try and fix everything I can within reason. My troybilt wouldn't start and after I did everything on the video it started. Your the best! Kim

Thanks that was very interesting to me because I have a 6.75 Quantum on a Snapper purchased in 2004 that was fitted with a different version of this carb that doesn't have the choke, but has some sort of a purge bulb primer system. Has a history of being difficult to start and restart since it was new and I used to think about trying to revert to the choke carb but wouldn't know if it was feasible but it was nice to see what it looks like. I guess they made this change for emissions reasons....who knows.

I must say I did like your video but, Yes there is a but Sorry. If you look back on the disassembly and the reassembly you reversed the position of the governor spring and the throttle cable. Does that make a difference? Im following right now but I'm going to reassemble the original way and if that doesn't work I'll reverse them. If im wrong please correct my ignorance. 3:58 and 17:28 timelines

I tried this fix on our neighbors Toro 22" Recycler, but it didn't work. It still starts then dies. Not sure what else to try; it runs fine if I spray carb cleaner into the carburetor so it seems like it must be a fuel delivery problem. Plenty of gas is getting through the fuel line to the carb. There was some debris in the gas when I drained the tank. Using fresh ethanol free gas did not help. It does have spark. Any other ideas about what to check? Should I try a fuel filter in the fuel line (a filter made for gravity feed engines), and re-clean the carb?

Lose the low Flashpoint gas as a cleaner and get a ultrasonic cleaner from harbor freight or solvent. I would have also asked the owner to show me the fuel can, 2 stroke oil being used, and mixing process. I use premixed fuel now. Did she check for spark? And finally these little motors do wear out. Topends, seals, crank rods, etc. flat wear out. And you can overoiil the air filter if it uses an oiled element.

Ty, I was wondering why my new mowers foam filter was covered in oil. Tried googling and wasn't getting immediate results.

well done, good step by step instructions

Perfectly done.

Excellent video. Thanks. MH

See this is what I want to see a regular person doing this stuff she isn't using anything that the everyday person doesn't have

With the float removed we see a shiny metal disk pressed into the plastic carburetor body. The disk in my carb had fallen out. What purpose does it serve? May I leave it out? If it must be installed how is that done so it won't fall out again?

Looks like she needs to buy 50.1 premix fuel, to much lugging the engine and to much oil in gas 😮

This was awesome! I see what folks mean. The other YT'ers are clueless by comparison. Side note: I wonder if I can get an aftermarket metal carb?

Great video. Thanks

And still no gas line filter after 20+ years.

I just fixed the toro and mowed the lawn for the first time this year! I love you beyond words! I want to send you chocolates! :D

That seems to be the magic trick! Thank you! My dad wanted to toss this mower out and just buy a new one. It was a father's day gift a few years back and now a father's day fix and savings 😊

Thanks for helping me fix my lawnmower..you r awesome

Hertz hired the GCOAT 😝

Thank you for your video, It worked first pull after this videos repair! Avoided spending 600 on a new "modern" electric mower

You a the BEST gas mechanic! 😁👍💪 🔥🔥🔥

Wellll finally I found you! I love your clear methodical style and good information. I have had my arsenal of mowing yard Maint gear preserviced as usual this year. All four pieces of equipment have failed to run…after returns to two different shops, for different reasons and one was way overfilled with oil (why? Dunno) I am now assigned as my mechanic!🤣 I have sorted out multiple issues already…my zero turn supposedly needed a new solenoid, it turned out to be dirty contacts at the harness connectors, my push small self propelled mower would not start after three returns to the shop, both are now repaired and run like a champ with your help. my pressure washer just serviced will not crank after a recent service I am now in this one…and this is from two different shops🤣🤣Looking at the carbs I realized that most were not cleaned and two had damaged gaskets or seals 😳😂 I have a large piece of property, and yearly I have all my gear serviced pre season, pay attention to my fuel (stabilize) and check for water… Well I am setting up as I go now to have the parts and tools to do these service and repairs myself. I will even buy an ultrasonic cleaner…way cheaper than to pay for the services. And fun, somehow I like doing this, it is meditative. I have always four small engine tinkering fun. Thanks for your channel it is a game changer. Another new “Girl” mechanic here! Cheers!

I squeeze the top lever way up on the top of the lawnmower push handle. It does not engage the throttle. Is there a spring or linkage missing? My customer's mower with this same carburetor (B&S 450e 125cc) I had replaced the needle and needle seat. Took out the atomizer assembly per your video here. Used guitar wire to clean out every hole and orifice then Put it all together. Everything is put back in place. Throttle linkage is properly attached to return spring but engine will not start unless I use starting fluid. Runs 3 seconds and dies.

I recently replaced the drive belt using this great video. However, the transmission tension spring fell off along with the upper bracket plate that the spring attaches to on the mower housing. I am having trouble figuring out where the plate goes on the housing. Anyone know? Thanks

LOVE it.

Thx! Fixed my front issue in just seconds after watching this!!!

Used an indicator on mine, but thought you were going to give advice on how to straighten. Guess you'd figure to replace it. I used a long pipe on the shaft, pulled on it many times but got it really close. Thanks

Great video, I’m about to rebuild my carb. I do have a question someone messed with the high and low screws and now I don’t know exactly where they need to be. Any suggestions on how to start from scratch on those screws?

Filter intrusive

These mowers must have the valves adjusted as part of their tune up. Without that, the mower will either stop, or not start. It's .006" on the intake, and .008" on the exhaust. The tune up is not complete without doing a valve adjustment. Everything else was spot on, except for the valve train tune up procedure, which is essential.

I have a toro tecumseh self pace mower 21inch new carb adjusted float new shut off cable..will start when primed then died runs a minute..what you think wrong

Love for you to do my tune up! So through!!

Well I did do it! Unfortunately, the lawn mower still not running....

Hello, Love your video's. They are very informative. I have a Honda mower HRR2169VYA which has an automatic choke. It starts and runs fine, but when it warms up and the choke is off it dies when you engage the blades. While the choke is still on the blades engage fine and the engine runs fine. But when the choke comes off the engine stalls when the blades are engaged. I have cleaned the carb, changed the plug, replaced the fuel, checked the gas cap, but I cant figure out why it stalls when its warm. HELP !

Awesome!!!

If you have time, you can get a new carb delivered for about twelve bucks on E Bay.

this mower has been nothing but problems for me. Fwd dies multiple times per year. Came broken out of the box! Just awful